104-IIRO-16

Isolated Digital Input and Relay Output Card

104-IIRO-16

The 104-IIRO-16 is a low-cost board that provides isolated input and output for PC/104 Bus computer applications. The board has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen electro-mechanical relay outputs. The Change of State Detection capability of ACCES' Model 104-IIRO-16 sets this board apart from the competition. An Economy version can be ordered as Model 104-IIRO-16E which has no Change of State Detection or IRQs. Also available is Model 104-RO-16 which has 16 relay outputs only. INPUTS The isolated inputs can be driven by either AC or DC and are not polarity sensitive. Input signals are rectified by opto-coupler diodes. A 1.8KΩ, ½ Watt resistor in series provides current limiting. The input voltage range is 3V to 28V (rms). To extend the input voltage range, you may connect external resistors in series with the input. Each input circuit is switch selectable for slow/fast filter that has a 4.7 millisecond time constant. The filter must be selected for AC inputs in order to eliminate response to AC noise. The filter is also valuable for use with slow DC input signals in a noisy environment. The filter may be switched out for DC inputs in order to obtain faster response. Filters are manually switched individually on or off. INTERRUPTS Interrupts are enabled/disabled by software. When the change-of-state detection circuit is enabled, the card asserts an interrupt whenever any of the sixteen isolated inputs change state. Once an interrupt has been generated and serviced, it is automatically cleared. This feature greatly frees up system resources by eliminating the need for constant polling to see when an input has changed state. OUTPUTS The electro-mechanical relay outputs are comprised of two groups of eight form C SPDT outputs. CONNECTIONS The relay outputs are accessed via a 50 pin header type connector, while the isolated inputs are accessed via a 34 pin type header connector.

  • Brand: Acces IO
  • 16 optically-isolated, non-polarized CMOS compatible digital inputs accept ±31VDC or AC rms
  • IRQ on input change of state (COS) eliminates the need for constant polling
  • Slow/fast filter to accommodate AC voltages and noisy DC inputs
  • 16 long-life form C electro-mechanical relays switch up to 1A each
-
+

Details

The 104-IIRO-16 is a low-cost board that provides isolated input and output for PC/104 Bus computer applications. The board has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen electro-mechanical relay outputs. The Change of State Detection capability of ACCES' Model 104-IIRO-16 sets this board apart from the competition. An Economy version can be ordered as Model 104-IIRO-16E which has no Change of State Detection or IRQs. Also available is Model 104-RO-16 which has 16 relay outputs only. INPUTS The isolated inputs can be driven by either AC or DC and are not polarity sensitive. Input signals are rectified by opto-coupler diodes. A 1.8KΩ, ½ Watt resistor in series provides current limiting. The input voltage range is 3V to 28V (rms). To extend the input voltage range, you may connect external resistors in series with the input. Each input circuit is switch selectable for slow/fast filter that has a 4.7 millisecond time constant. The filter must be selected for AC inputs in order to eliminate response to AC noise. The filter is also valuable for use with slow DC input signals in a noisy environment. The filter may be switched out for DC inputs in order to obtain faster response. Filters are manually switched individually on or off. INTERRUPTS Interrupts are enabled/disabled by software. When the change-of-state detection circuit is enabled, the card asserts an interrupt whenever any of the sixteen isolated inputs change state. Once an interrupt has been generated and serviced, it is automatically cleared. This feature greatly frees up system resources by eliminating the need for constant polling to see when an input has changed state. OUTPUTS The electro-mechanical relay outputs are comprised of two groups of eight form C SPDT outputs. CONNECTIONS The relay outputs are accessed via a 50 pin header type connector, while the isolated inputs are accessed via a 34 pin type header connector.

Ordering Info

  • 104-IIRO-16
  • 104-IIRO-16E
  • 104-RO-16

Downloads

Assured Systems Datasheet (PDF)

A PDF edition of this page with supporting manufacturer datasheets

System Integration

Please ask about how we can configure your solution

Global Operations

We deliver and support products via offices globally

Full Warranty

Industry leading warranties on all solutions as standard

Technical Support

Experienced engineers are on hand to support your project

Can't Find What You Want?

Specification

  • 16 optically-isolated, non-polarized CMOS compatible digital inputs accept ±31VDC or AC rms
  • IRQ on input change of state (COS) eliminates the need for constant polling
  • Slow/fast filter to accommodate AC voltages and noisy DC inputs
  • 16 long-life form C electro-mechanical relays switch up to 1A each

Delivery Information

Orders dispatched from Assured Systems USA will be delivered using FedEx.

Payment Methods & Options

Accepted payment methods for US customers include bank transfer, VISA or Mastercard in USD.

ACCES I/O: Warranty and Service Information

All ACCES I/O products distributed in the EMEA come with a 2 year warranty as standard, with additional extension options available upon request. As an official ACCES I/O partner, we are proud to provide customers with peace of mind and the highest quality products, including any systems which have been configured to meet individual specifications.

Related Products

You may also like...

PCI-COM422/4

4-port PCI RS-422 Serial Communication Card

USB-FLEXCOM4

4-Port USB to Serial RS-232/422/485 Adapter

104-COM-8S

PC/104 2, 4 & 8-Port RS-422/485 Serial Communication

PCI-COM232/2

2-port PCI High-Speed RS-232 Serial Communication Card