PCI-ICM-2S

2-port PCI Isolated RS-422/485 Serial Communication Card

PCI-ICM-2S

The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed. By means of jumper placement on the card, each port can be set up for either RS-485 or RS-422 operation. RS-422 operation uses differential balanced line drivers for long range and high noise immunity. RS-485 operation improves on that by providing multi-drop capability for as many as 32 devices. RS-485 communication requires that one device on the network provide a bias voltage to ensure a known “zero” state when all transmitters are off. Also, receiver inputs at each end of the network should be terminated to avoid “ringing”. Both ports on PCI-ICM-2S support those needs by means of jumpers on the cards. The card supports half-duplex and full-duplex communications in 2- and 4-wire cable connections. Half duplex allows traffic to travel in both directions, but only one way at a time. In full-duplex operation, data travels both ways at the same time. Most RS-485 communications use the half-duplex mode because only a single pair of wires needs to be used and installation costs are dramatically reduced. In RS-485 operation the driver must be enabled and disabled as needed to allow all cards to share a two wire or four wire cable. Control circuits on PCI-ICM-2S enable the driver when data are to be transmitted. When transmission is complete, the driver remains enabled for the transmission time of one additional character and then is automatically disabled. The receiver at that port is disabled during transmission time and then enabled at the completion of data transmission. Type 16550 UART’s are used. These include 16-byte FIFO buffers to protect against data loss in multitasking operating systems. A crystal oscillator is located on the card. This oscillator and supporting circuits provides means for precise selection of baud rates up to 115,200. Rates up to 460,800 are available by jumper selection.

-
+

Details

The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed. By means of jumper placement on the card, each port can be set up for either RS-485 or RS-422 operation. RS-422 operation uses differential balanced line drivers for long range and high noise immunity. RS-485 operation improves on that by providing multi-drop capability for as many as 32 devices. RS-485 communication requires that one device on the network provide a bias voltage to ensure a known "zero" state when all transmitters are off. Also, receiver inputs at each end of the network should be terminated to avoid "ringing". Both ports on PCI-ICM-2S support those needs by means of jumpers on the cards. The card supports half-duplex and full-duplex communications in 2- and 4-wire cable connections. Half duplex allows traffic to travel in both directions, but only one way at a time. In full-duplex operation, data travels both ways at the same time. Most RS-485 communications use the half-duplex mode because only a single pair of wires needs to be used and installation costs are dramatically reduced. In RS-485 operation the driver must be enabled and disabled as needed to allow all cards to share a two wire or four wire cable. Control circuits on PCI-ICM-2S enable the driver when data are to be transmitted. When transmission is complete, the driver remains enabled for the transmission time of one additional character and then is automatically disabled. The receiver at that port is disabled during transmission time and then enabled at the completion of data transmission. Type 16550 UART's are used. These include 16-byte FIFO buffers to protect against data loss in multitasking operating systems. A crystal oscillator is located on the card. This oscillator and supporting circuits provides means for precise selection of baud rates up to 115,200. Rates up to 460,800 are available by jumper selection.

Ordering Info

  • PCI-ICM-2S: 2-port PCI Isolated RS-422/485 Serial Communication Card

Downloads

System Integration

Please ask about how we can configure your solution

Global Operations

We deliver and support products via offices globally

Full Warranty

Industry leading warranties on all solutions as standard

Technical Support

Experienced engineers are on hand to support your project

Can't Find What You Want?

Specification

  • Universal PCI, PCI-X, 3.3V and 5V compatible
  • Optically isolated, asynchronous serial communications
  • Two independent ports each supports RS-422 or RS-485 communications
  • Type 16550 buffered UARTs protect against data loss in multitasking systems
  • Baud rates up to 460,800 baud
  • Usable at cable lengths up to 4,000 feet
  • Detected as standard COM ports under Windows

Delivery Information

Orders dispatched from Assured Systems USA will be delivered using FedEx.

Payment Methods & Options

Accepted payment methods for US customers include bank transfer, VISA or Mastercard in USD.

ACCES I/O: Warranty and Service Information

All ACCES I/O products distributed in the EMEA come with a 2 year warranty as standard, with additional extension options available upon request. As an official ACCES I/O partner, we are proud to provide customers with peace of mind and the highest quality products, including any systems which have been configured to meet individual specifications.

Related Products

You may also like...

USB-COM232-4A

4-Port USB to Serial RS-232 Adapter

PCI-COM422/4

4-port PCI RS-422 Serial Communication Card

PCI-COM2S

2-port PCI RS-232/422/485 Serial Communication Card

USB-485

1-port USB to RS-485 Serial Adapter